PLQE040 The PLQE040 with frame size 040 complements the successful Economy planetary gearbox series PLQE, for which a total of four frame sizes between 040 and 120 are now available. With a centering collar diameter on the output side of just 35 mm, the newcomer presents itself as a true "mini powerhouse" in the Economy family. Depending on the gear ratio, it can transmit nominal torques of up to 20 Nm. The total length of the gearbox, incl. adapter, is just over 9 cm, depending on the selected motor adapter. As on all PLQE gearboxes, the square output flange of the PLQE040 allows uncomplicated mounting on the system without intermediate adapters. Despite its small size, the new PLQE gearbox has high-performance deep groove ball bearings on the output shaft, so that considerable radial forces of up to 390 newtons can still be absorbed here. It is offered with 24 different gear ratios from i=3 to i=512 and is available with either a smooth output shaft or a keyed shaft. PLFE055 With the new PLFE055, the PLFE Economy gearbox series with a flanged output now offers four frame sizes, starting at 055. This newcomer is available in 1- and 2- stage versions and with gear ratios from i=3 to i=100. The centering collar diameter here is 5.5 cm and, depending on the gear ratio, can transmit torques of up to 32 Nm. The support spacing of the deep groove ball bearings on the output side largely corresponds to the larger model PLFE064, so that the PLFE055 can support almost the same radial forces and breakdown torque despite its more compact dimensions. Its flange interface makes it particularly easy to install.

Exceptionally high speed and dynamics With its speed and torque, the new AM3248 stepper motor from FAULHABER raises the bar in terms of performance and dimensions. Offering up to 10,000 rpm, it can achieve five times the speed of comparable stepper motors. Combined with a gearhead reduction of 100:1, it supplies a torque of 5 Nm. The motor delivers these values with a diameter of just 32 mm. This makes it ideally suited for a wide range of applications in areas such as aerospace, laboratory automation, large optical systems, the semiconductor industry, robotics and 3D printing. The multi-pole, two-phase AM3248 stepper motor performs 48 steps per revolution and offers a very high holding torque of 85mNm. The motor starts with a high speed from the very first step; thanks to its low inertia, it can be used in applications that require very fast acceleration and fast changes of direction. Newly developed large ball bearings further extend the already long service life of this motor type. For its size class, the performance values that it achieves in combination with a 32 GPT gearhead are unrivaled on the market. The motor can also be combined with an IE3 magnetic encoder. These properties and options make the motor ideally suited for a variety of demanding applications. This includes aligning the solar panels of satellites, for example. The motors move the booms so that the panels are always directly facing the sun. In addition to working precisely and reliably over many years, the motors must also be able to withstand the extreme temperatures in outer space. In the semiconductor industry, very high dynamics and speed are required when positioning the wafers in very confined installation conditions in the machines. This is another application in which the highest level of precision and reliability are essential.

Optimised for performance, the new FS500i-A will offer a number of important innovations. For instance, operators are set to benefit from FANUC’s new iHMI2 CNC interface, which maintains the appealing look and feel of FANUC’s iHMI but combines it with the familiar operability of legacy systems. For every task, all interactions can be handled on one screen so that there is no need to jump between several of them. The FS500i-A will also provide the potential to program PMC (programmable machine control) systems using ISO-defined Structured Text language, while a further new function is the simplification of processes that require programming in five axes. Specifically, using a special tool, the future FS500i-A offers the ability to accommodate any arbitrary machine kinematics.

The next generation of machines offers significantly greater customer benefits and can do many things better, more easily, and more comprehensively than its predecessor. However, this often requires a new control system. Throughput time and quality during efficient system implementation and application execution are the critical performance indicators. Clear structures, transparent processes, and modular concepts are the key success factors for efficiently launching new machine generations.

Pizzato CS AM series safety modules benefit from important technological advancement. Major new features include sensorless speed monitoring, more sophisticated motor control through parameterisation of the modules via software, and the ability to monitor motor operating data in real time. > Three different versions available The new series now includes three different types of safety modules, available both in permanently programmed or configurable version: CS AM1• : Motor standstill monitoring CS AM2• : Monitoring of motor speed and direction of rotation CS AM3• : Combines the functionalities of both CS AM1• and CS AM2• The configurable version is equipped with a USB Type-C port, allowing the device to be configured using the CS AM Configurator, developed in-house by Pizzato Elettrica. The software can be downloaded by the user free of charge. It is also possible to choose between safety outputs with OSSD or relay technology. Modules with OSSD outputs are 22.5 mm wide, while those with relay outputs are 45 mm wide. > Inductive sensor for the detection of specific faults With the CS AM2• and CS AM3• versions, an inductive sensor can be connected to the module to detect faults not normally detected by products currently on the market. > Adjustment of monitoring parameters The CS AM Configurator software is divided into several sections: Project, Setting and Monitor. In the Project section, all relevant project information is entered and the required function can be selected and configured for each input and output of the module. In the Setting section, parameters for the detection of motor standstill can be set, thresholds for minimum and maximum speed thresholds defined, and the detection of the motor's direction of rotation enabled. In the Monitor section, the status of the module's outputs, the residual voltage detected on the phases, the speed and the direction of rotation of the motor can be monitored and saved in real time.

With the launch of the IEP3, FAULHABER expands its product line with an incremental encoder which, thanks to the latest chip technology, achieves a very high resolution and accuracy. With a diameter of just 8 mm, the IEP3 is very lightweight and compact yet still offers a resolution of up to 10,000 lines per revolution – made possible by the latest chip technology with high interpolation. In the standard version, the resolution is freely programmable from 1 - 4,096 lines per revolution. Moreover, the chip technology that is used ensures a high positional accuracy of typically 0.3 °m as well as a high repeatability of typically 0.05 °m thanks to accuracy compensation.

The Sendix K58 (size 58 mm) and K80 (size 80 mm with large hollow shaft) encoders also impress with their new, future-proof technology - they are ideal for integration into future IIoT environments and will feature a digital type plate in the future. The robust construction with advanced Safety-Lock™ design, long service life and versatile application options make the new Sendix encoders the ideal choice for your application. An innovative housing design that is standardized for each size enables designers to achieve maximum simplicity and efficiency without compromising on mounting type, installation depth, size or installation space. This means that the designer has only one standardized design-in concept across all new variants.

The new generation of the proven OGD distance sensors now offers an even wider range to suit all applications. Precise measurements at short distances are just as easy as object detection over ranges of up to 4 metres.

The i4L is a compact SCARA robot which offers strong performance at the lowest cost of ownership. The i4L robot is capable of high speed, high-precision motion with payloads up to 5kg. Its compact design and flexible programming make it ideal for a wide variety of robot applications including digital assembly. Key Specifications - 5 kg payload capacity - 350 mm, 450 mm, and 550mm reach options with table and wall mounting options - Fast cycle time with an unprecedented range of movement and repeatability - Exceptionally powerful built-in servos to handle payloads with ease - Advanced and robust industrial design - Lowest total cost of ownership - Optimize your line with maximum uptime by means of interactive maintenance alarms and an RGB dome light

Gigabit networking directly at the machine without an additional cabinet: the new IP67 Lean-Managed Switch combines robust M12 connectivity with straightforward OT diagnostics. Eight Gigabit M12 ports, an operating range from −40 to +70 °C and a rugged IP67 design allow direct installation on machine modules, conveyor systems or robotic cells. Web-based management, a diagnostic dashboard and topology view simplify commissioning and troubleshooting without in-depth IT expertise. VLAN structures, data prioritization and multicast handling support a stable and transparent network infrastructure.

NX series RFID safety switch with lock is the world's smallest device in its category. > Maximum technology in the minimum volume Its dimensions of just 30x30x94.5 mm, and its volume of only 85 cm3 make the NX series safety switch, the smallest in the world in its category. > High safety standards guaranteed This switch offers all the well-established features of the Pizzato brand, such as the RFID technology installed in the actuator and the highest guaranteed safety levels PL e and SIL 3. > Metal head and technopolymer body The housing of this device is made of two different materials: the metal head ensures maximum impact and strength when the door is locked, and the technopolymer body ensures the lightweight and flexible construction of the device. > Fast diagnosis of operational state thanks to the RGB LEDs The illuminated cap positioned on the head of the device allows a quick diagnostic of inputs and outputs functional states. > Bistable operating principle This new operating method activates the internal solenoid by means of short electrical impulses that stabilise its position in either the unlocked or locked state. The most significant advantage resulting from this is the considerable reduction in energy consumption and warming up of the switch. > Straightforward mounting Mounting is carried out using just two M5 screws on the front with a hole spacing of 20 mm, whereby it plays no role whether the doors open to the right or left or if they are sliding or hinged doors. This is achieved by the presence of three entry openings for the actuator, which eliminate the need to rotate the head or the switch. > Recent updates for this device: - Three auxiliary releases in a single device, one corresponding to each actuator input - Various connection options: with an integrated M12 connector connection, cable wiring with variable cable length (up to 10 metres) or cable wiring with cable length up to 3 metres and M12 connector at the end.

The new P-KUBE Lite safety handle joins the P-KUBE family, for an even wider range of devices. This new model, made of a strong technical plastic, is ergonomic and functional whilst maintaining the distinctive modern design of the P-KUBE family. The handle is compatible with FG and FY series safety locking switches. The sliding grip enables easy and immediate activation of the switch. With the actuator fixed directly to the handle, its removal is impossible, ensuring a greater level of security. The symmetrical design of the P-KUBE Lite safety handle makes it unique on the market and enables installation from multiple sides, regardless of its configuration. It can be installed on hinged or sliding doors, both on the left or right side. The strong centring pin on the handle has a dual purpose: It means the actuator must be correctly inserted into the switch, preventing misalignment of the doors and consequent failed activation of the switch. It prevents direct collision between the switch and actuator in the event that the door is closed with force. The use of snap-on protection caps prevents tampering with fixing screws on the handle and enables free installation with standard screws instead of tamper-proof screws. Integration options - Block button; - Key lock; - Device for locking the handle in the open position; - Lock-out system; - Internal lever for emergency escape.

Hanser is expanding its portfolio with a completely new product family: a thoroughly designed selection of various casters and wheels. Hanser’s standard parts selection is growing once again – with the recent addition of an entirely new category for wheels and casters. The establishment of the new catalog group 3.10 is a clear indication that these mobility-enabling standard parts will have all the room they need. That is only logical given that the wheels and casters serve to complement their proven but static leveling feet relatives, which are available in many different versions. As always, Hanser is entirely focused on practical requirements: the individual types are organized according to the applicable ISO testing procedures, making it easy to associate them with the most important configuration parameters. For example, the new range includes light duty casters with low load capacity, medium duty casters for industrial use and heavy duty casters designed for high dynamic loads coupled with higher travel speeds. Casters are ready-to-install parts consisting of a wheel and a bracket, with the latter generally made of bent sheet steel, except for the heavy duty versions of welded steel. The bracket, available in swivel or fixed versions, holds the wheel and serves for mounting the caster. Fixed casters provide lateral guidance to ensure stable travel both straight and on curves. The swivel brackets with ball bearings enable maximum maneuverability with 360-degree rotation and movement in any direction, a property that is particularly advantageous in tight spaces. Optionally integrated total lock brakes prevent the wheel from turning or rotating in the steering axis, and variants are also available with extendable leveling feet for an even more secure stand. More information on Hanser standard parts can be found on the internet at Hanser.ch

Always order the latest and most innovative products.

Pizzato Elettrica introduces the new P-KUBE Krome series, which combines the characteristics of a robust handle for safety enclosures with an ergonomic, rounded grip and built-in, customisable control button, with various illuminated signalling options. These indicate the state of the guard or other operating conditions. The new P-KUBE safety handles are a built-in and innovative solution which permits to optimise the cost of components by eliminating peripheral control boxes and illuminated signalling columns. Key features: - Internal, 5 mm thick steel fixing plate to ensure locking system robustness and increased service life. - Handle front customisable in satin chrome and illuminated white finishes (this last version will be available in the first quarter of 2019) - High signalling visibility in many different colours - Tamper prevention and high anti bypass coding level thanks to RFID technology actuators - Requires no adaptation for use on hinged or sliding doors, left or right