simatec ag is an independent, internationally operating family-owned company based in Wangen an der Aare, Switzerland, and has been managed by Mischa N. Wyssmann, the second generation of the family, since 2005. Since the company was founded in 1983, motivated employees have been developing and producing innovative products for the maintenance of rolling bearings. Globally renowned brand names such as simatherm, simatool, and simalube originate from simatec.

Reduce costs with simatherm Investing in a simatherm induction heater pays off in a number of ways. Within seconds, a roller bearing is gently heated to the required mounting temperature. This results in a huge saving in time, energy and money compared with previous heating methods such as oil baths, heating plates or ovens. A component is heated to the preselected temperature, where it is maintained using the keep-warm function, which means that it is never overheated and is ready for mounting at any time. A further advantage is that the temperature of the components is monitored using a temperature sensor and displayed on the unit. Fast heating possible The recommended heating temperature for mounting roller bearings is 110°C. With average bearing sizes, this temperature is reached after a matter of seconds, which saves both time and money. Besides heating bearings, however, simatherm units can also be used to heat other circular metal components such as gear wheels, flanges, bearing rings, pinions, etc. Temperature monitoring allows components to be warmed to a maximum of 250°C. Depending on the material and dimension of the components, they can even be heated to 400°C in time mode. Easy mounting The compression force required for mounting increases considerably as the bearing size increases. If the heat expansion of the metals is utilised, it is possible to mount bearings and other circular components on a shaft or in a housing without exerting any force. When heating a component, the simatherm unit remains cold and is therefore safe to touch. Plastic seals and lubricant also do not become hot. This also allows pre-lubricated bearings to be heated, which is a unique advantage of simatherm units. The grease is not damaged when the bearings are heated, and the latter can be mounted as soon as the preselected temperature is reached.

sf elektro-engineering ag verbindet mit der Firma Siemens eine langjährige Solution-Partnerschaft für Automation, Cranes und Drives. Bezüglich SPS decken wir S5 bis hin zu den modernsten Familien der S7 mit TIA-Portal oder WinCC ab. Die Modelle der Drives G-, V- und S120/S150 inklusive Safety werden von sf-ag dimensioniert, geplant, programmiert, parametriert und in Betrieb gesetzt. Damit eine kurze Inbetriebsetzung gewährleistet werden kann, verfügt sf-ag über ein mächtiges Simulationssystem.

simatool tool sets enable fast mounting and dismounting of roller bearings and radial shaft seals. They are used successfully throughout the world in the mechanical engineering industry, in maintenance workshops and practically all other branches of industry. The fast, safe precision handling of the tools is particularly valued. Compact, sturdy tool case All simatool tool sets are supplied in hard-shelled tool cases. These ensure the required protection of high-quality tools at all times. The compact tool cases allow easy use of the tools in any sector. User video on the Internet To ensure correct handling of simatool tools, simatec ag has provided informative and practical user videos at simatec.com www.youtube.com: Keyword: "simatool"

By using our new micro injection molding machine, we are taking precision and repeatability in the production of small parts and rubber-metal composite parts to a new level for all types of elastomers. WHY CHOOSE MICRO FUNCTIONAL PARTS FROM KUBO? Decades of experience in toolmaking and internal production of elastomeric moulded parts Support in the development of your parts by a specialized and experienced engineering team comprising material, plastic, and mechanical engineers Effective/optimal implementation thanks to our in-house toolmaking Selection of the right rubber compound due to material expertise Precise manufacturing at our facility in Effretikon, Switzerland Reliable quality control through modern digital measurement technology High-quality products you can rely on SPECIFICATIONS From single pieces to mass production Complex moulded parts (multi-plate moulds) Smallest parts, e.g. O-rings with inner diameter Ø 1.5 mm and cord thickness of Ø 1 mm, valves with a diameter of 2.4 mm and height of 2.2 mm, vulcanization of a metal part onto a rubber part with a diameter of Ø 3 mm and a thickness of 0.4 mm High-precision injection volume Tolerances according to ISO 3302 manufacturing class M1 achievable for parts under 1 mm All common elastomers (NBR, EPDM, etc.) Processing of high-performance elastomers such as FFPM, FPM

ABB’s new condition monitoring solution for low voltage motors A new era of remote condition monitoring for low voltage motors has arrived. ABB Ability™ Smart Sensor picks up data on vibration, temperature and other parameters and uses it to reduce motor downtime by up to 70 percent, extend lifetime by as much as 30 percent and lower energy use by up to 10 percent. ABB has developed a compact ABB Ability™ Smart Sensor that is attached to the frame of low voltage induction motors. No wiring is needed. Using on-board algorithms, based on ABB’s decades of motor expertise, the ABB Ability™ Smart Sensor relays information about the motor’s health, via a smartphone and over the internet, to a secure server. This solution can make huge numbers of motors into smart devices, enabling them to benefit from intelligent services.

The GS Service software offers a holistic solution for digital operations management and maintenance. With its modular structure, the system covers all relevant areas – from the structured mapping of assets and resources to personnel and task management and efficient fault and defect processing. The software enables centralized management of fleets, equipment, tools, and personal protective equipment, as well as precise organization of personnel resources. Integrated modules for fault and defect management support responsive and documented maintenance. Consistent interfaces and robust document management ensure clear processes and information availability. The system is complemented by powerful tools for reporting, materials management, time recording, measurement data management, and project planning. The notification service ensures practical communication between all parties involved. The software thus makes a decisive contribution to optimizing operational processes, increasing cost transparency, and increasing resilience.

Lanz-Anliker has been successfully active in the field of filtration for several years. The filters we manufacture are used in wet and dry filtration. We are represented with our products in chemistry, medicine, food production and drying, paper industry, aquaculture, water treatment, laundry technology, etc.. For the production of our filter media we only use high-quality synthetic screen and filter cloths. We have a large number of monofilament and multifilament fabrics made of polyamide, polyester, polypropylene, Teflon, ECTFE, ETFE, etc. at our disposal. Our quality management system according to ISO 9001:2008/ISO 13485:2003/AC:2007 and 14001:2015 is your guarantee that you will receive only first-class products.

The NIV specialist seminars offer you the opportunity to keep your knowledge of electrical safety, standards and regulations up to date. We have interesting topics ready for you. The following topics are covered in the seminars: - Stray currents in agricultural operations - Emergency power supply - Photovoltaic system: Checking during commissioning and performance monitoring - Voltage quality in PV systems - Checking AC electric charging stations - Device testing for the practitioner (live check)

The spiral tube heat exchanger essentially consists of a jacket and a spiral tube bundle. The finned tubes are built into a spiral in the jacket, which creates a long thermal path. Spiral finned tubes produce high levels of turbulence that help reduce contamination. The bundle tubes can expand optimally. Flow rate: 1-300m3 / h Operating pressure: 16-40 bar Connections: 11/4 “-DN 150 Recommended max. Temperature difference: 150 ° C Materials: 1.4401 / titanium benefits High performance: Spirally finned tubes compactly installed, give the heat exchanger a large exchange surface with a high thermal output. Compact and light design, large number of different models and equipment for different applications. applications Different applications: Applicable for a wide range of different pressure, flow and temperature conditions. Ideal for steam and hot water, district heating, swimming pool Stock Up to DN 100 material in stock

STABURAGS NBU 30 PTM is a water-resistant assembly grease containing solid lubricants that specifically combats fretting corrosion. It is ideal for outdoor applications exposed to high levels of moisture. The product has proven itself as an assembly grease for clearance fits, water and hot water fittings, and sliding guides – particularly on filling machines, valve spindles, and cylinder guides. It can also be used for bolts, spindles, screws, and other sliding guides.

Zur Absperrung von Durchgangsventilen mit unterschiedlichen Handraddurchmessern, aus beständigem Polypropylen – ausgezeichnete Schlag- und Chemikalienbeständigkeit.